Getting Started with Plumbing Basics for Bathtub Installation
Getting Started with Plumbing Basics for Bathtub Installation
Blog Article
We've unearthed this post relating to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround directly below on the net and thought it made sense to write about it with you on this page.
Mounting a bath tub isn't specifically brain surgery, but it does need solid plumbing, carpentry, and also often, tiling skills. Replacing an old bathtub with a new one is likewise a reasonably difficult job. If the old bathtub is easily obtainable, the project can move rapidly; if you need to open a wall surface to eliminate the old bathtub and also place the brand-new bathtub, the task is much harder. In either situation, the project is within a house handyman's abilities, although you will certainly need a helper to leave the old tub and also embeded in the new one. Make certain you have certified on your own for the work and also are comfortable attempting it. Rather than working with a service provider to take control of a halfway-completed project, it is much better to think about utilizing one before you start. Possibilities are you might require an expert plumber to make tube connections.
This article will aid you mount a brand-new bath tub in your washroom if you have currently acquired a new tub as well as do not require to change the plan of your previous water system pipes.
Your devices and product list ought to consist of the following:
Removing Old Taps
If you need to change old taps with new ones as a part of your setup, then the first thing you ought to do is separate the water. After doing so, turn on the faucets to drain any type of water staying in the system. The procedure of eliminating the existing taps can be quite problematic as a result of the restricted gain access to that is usually the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the taps. Have a towel ready for the staying water that will certainly originate from the pipes. As soon as the supply pipes have been removed, utilize the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from transforming throughout this process. Once the faucets have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing compound.
Prior to going on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Suitable New Touches
If the tails of the new taps are plastic, then you will need a plastic adapter to prevent damages to the string. One end of the port fits on the plastic tail of the tap and also the other end supplies a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will call for decreasing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the mounting hole in the bath/basin ensuring that the washing machines remain in place between the tap and also the sink. Secure the faucet in position with the producer given backnut. When the tap is firmly in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with regular faucet connectors. The previous type should be connected to the tap finishes first, tightening just by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Installing the Tub
Using both wood boards under its feet, position the tub in the required setting. The wood boards are helpful in uniformly spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto four little factors.
The following goal is to make sure that the tub is leveled all round. This can be accomplished by checking the level and also adjusting the feet on the bath tub until the level checks out level.
To set up taps, fit all-time low of the outermost adaptable tap port to the suitable supply pipe by making a compression join; then do the very same for the other faucet.
Turn on the water and also inspect all joints and brand-new pipework for leaks and also tighten them if needed. Fill up the bathtub and likewise examine the overflow electrical outlet and also the typical outlet for leaks.
Ultimately, take care of the bathroom paneling as defined in the manufacturer's instruction manual. Tiling as well as sealing around the bathtub ought to wait up until the bath tub has actually been made use of a minimum of once as this will certainly settle it right into its final setting.
Planning for the Installation
First of all, the sustaining frame supplied with the bathroom ought to be fitted (if needed) according to the maker's instructions. Next, fit the taps or mixer to the bathtub. When suitable the tap block, it is necessary to make certain that if the tap comes with a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bath, it is additionally sensible to fit a sustaining plate under the taps unit to avoid stress on the bath tub.
Fit the flexible tap connectors to the bottom of the two faucets making use of 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet via the hole in the bath. Utilize the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make certain you use all of the provided washing machines.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bath ought to now prepare to be fitted in its last placement.
Tiling Around the Tub
In the location where the bathroom satisfies the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the installation can move enough to break a rigid seal, causing the water to penetrate the wall between the bathroom and the tiling, bring about problems with wetness and possible leakages to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your fixtures and fittings. They are sold in tubes and cartridges, as well as can securing voids up to a size of 3mm (1/8 inch). If you have a larger space to load, you can load it with spins of soaked newspaper or soft rope. Remember to always load the bath tub with water prior to sealing, to permit the activity experienced when the tub is in usage. The sealant can fracture fairly early if you do not take into account this activity prior to securing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also conveniently readily available on the marketplace. It is recommended to fit the floor tiles using waterproof or water-proof adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm just very intrigued by How to Install a Bathtub Yourself and I am assuming you appreciated the entire page. Do you know another person who is interested by the subject? Be sure promote it. Thanks for your time. Visit again soon.
About This Report this page